DS200CTBAG1A GE Mark V Analog Termination Board - Turbine Control

Product Overview

The DS200CTBAG1A serves as a sophisticated Analog Termination Module (CTBA) within the General Electric Mark V LM turbine control environment. Engineered for the R5 core, this printed circuit board manages critical I/O signals, including shaft parameters and analog loops. It acts as the primary link between the controller and the plant field instrumentation, ensuring reliable data acquisition and command distribution.

Technical Specifications

• Brand/Manufacturer: General Electric
• Series: Mark V LM
• Part Number: DS200CTBAG1A
• Board Function: Analog Termination (CTBA)
• Revision: 1 A
• Dimensions: 6.25 in x 4.25 in
• Operating Temperature: -28°C to 55°C
• Protection: Integrated resistors, capacitors, and 23 MOV (Metal Oxide Varistors) for voltage surge suppression
• Communication Ports: RS-232 9-pin D-shell (TIMN diagnostics), IONET, and ARCNET

Diagnostic and Control Capabilities

The DS200CTBAG1A board is designed for robust system oversight. The integrated RS-232 port facilitates deep-level TIMN diagnostic access, allowing technicians to verify signal integrity in real-time. The board features a sophisticated bypass relay mechanism; should internal power fail, the relay ensures continuous COREBUS communication to maintain operational availability. Its onboard hardware jumpers (BJ1-BJ15) allow for precise field-level configuration of signal references and DCOM isolation.

Connectivity and Integration

This module acts as a central hub for inter-board communication. Key interface points include:

• Signal Management: JAA (4-20 mA output) and JBB (Shaft data/4-20 mA input) interfaces to the TCCA board.
• Networking: 8PL (IONET to STCA), JX (IONET to TCDA), and JAI/JAJ (COREBUS to QTBA).
• Power Management: JPD connector for TCPD board 24V dc power monitoring.

Global PLC Spare HUB's Insight

In our experience, the DS200CTBAG1A is prone to environmental stressors due to its location in the turbine core. We recommend periodic inspection of the 23 red varistors for thermal degradation. When integrating this board, always verify that termination resistors are present on unused COREBUS ports (JAI/JAJ) to prevent signal reflections that cause erratic turbine readings.

Typical Applications

• Gas, Steam, and Wind Turbine Automated Drive Assemblies
• Speedtronic Control System Upgrades and Retrofits
• Precision Analog Loop Monitoring
• Critical Turbine Core Data Processing

Ordering and Logistics

• Warranty: 12-month standard replacement warranty.
• Shipping: Expedited global logistics via FedEx, UPS, and DHL.
• Processing: Rapid 24-48 hour dispatch window.
• Package Includes: DS200CTBAG1A PCB, factory-tested and ready for installation.

Frequently Asked Questions

What is the purpose of the 6PL connector on this board?
The 6PL connector is a vestigial structure and remains unused during the standard operation of the DS200CTBAG1A module.

How can I confirm if my board is properly referencing DCOM?
Use the hardware jumpers BJ1 through BJ14 to connect the negative terminal of your mA inputs to the DCOM reference, ensuring a stable signal ground.

Should I be concerned about signal interference on the COREBUS?
If you are not utilizing the JAI or JAJ ports, you must install an external termination resistor to ensure bus impedance remains within the Mark V specifications.

Why does the board include so many varistors?
The 23 integrated varistors provide essential protection against transient voltage spikes, which are common in heavy-duty turbine control cabinets.

What is the best way to verify if the bypass relay has triggered?
If the board loses primary power, the diagnostic system will reflect a failure in COREBUS communication status; check the 24V dc input at the JPD connector first.

Procurement and Selection Guide

• Verify your current hardware revision is compatible with the 1A suffix.
• Always inspect the physical pins on D-shell and COREBUS connectors for oxidation before insertion.
• Ensure your maintenance team has the GEH-6153 manual available for mapping jumper settings to specific turbine configurations.

Tags