Bently Nevada 3500/40-03-00 Proximitor Monitor | 3500/40 Series I/O Module
Manufacturer: Bently Nevada
Product No.: 3500/40-03-00
Condition： In stock
Product Type: Proximitor Monitor
Product Origin: USA
Payment: T/T, Western Union
Weight: 910g
Shipping port: Xiamen
Warranty: 12 months
Estimate delivery times: 12-26 days (International), 3-6 days (United States).
Return within 30 days of purchase. Duties & taxes are non-refundable.
Guaranteed Safe Checkout
Product Overview
The Bently Nevada 3500/40-03-00 is a four-channel machinery protection monitor.
It processes signals from eddy current proximity probes within the 3500 Series framework.
The module continuously compares measured static parameters against programmed alarm setpoints.
Engineers configure each channel for shaft vibration, thrust position, eccentricity, or REBAM measurement.
Integrated internal barriers allow direct connection to probes located in hazardous process areas.
Configuration Breakdown
- Base Monitor: 3500/40 — 3500/40 Proximitor Monitor
-
I/O Module Type: -03 — Proximitor I/O Module with Internal Barriers and Internal Terminations
- Includes built-in Zener safety barriers for intrinsically safe sensor loops.
- Uses direct screw-terminal blocks located on the rear I/O card.
- Agency Approval Option: -00 — No agency approvals required
Technical Specifications
| Parameter Category | Specification Details |
| Brand & Manufacturer | Bently Nevada |
| Part Number & Series | 3500/40-03-00 (3500 Series) |
| Signal Inputs | Accepts 1 to 4 proximity transducer signals (10 kΩ input impedance) |
| Power Consumption | 7.7 Watts typical operational draw |
| Transducer Power Output | -24 Vdc supply to field proximity sensors |
| Radial Vibration Sensitivity | 3.94 mV/µm (100 mV/mil) or 7.87 mV/µm (200 mV/mil) |
| REBAM Sensitivity Range | 40 mV/µm (1000 mV/mil) or 80 mV/µm (2000 mV/mil) |
| Direct & Gap Accuracy | Within ±0.33% of full-scale typical (±1% maximum) |
| Frequency Response (Radial Direct) | User-programmable single-pole filter (4 Hz to 4000 Hz or 1 Hz to 600 Hz) |
| Front Panel Indicators | OK LED, TX/RX LED, and Bypass Mode LED |
| Buffered Outputs | Four front-panel coaxial connectors (550 Ω output impedance) |
Installation & Wiring Considerations
- Install the rear I/O module into the matching chassis slot behind the main monitor card.
- Land field wiring directly onto the internal termination blocks using correct wire gauges.
- Maintain a dedicated intrinsically safe ground connection for internal barrier protection circuits.
- Connect diagnostic instruments to the front buffered coaxial outputs without impacting primary monitoring.
- Ensure field cables stay separate from high-voltage AC lines to prevent signal interference.
Commissioning & Software/Firmware Requirements
Commissioning the 3500/40-03-00 requires specific software and firmware versions.
- Standard Operation: Requires 3500/01 Software (v2.50) and 3500/02 Software (v2.20).
- REBAM Operation: Requires 3500/40M Module Firmware (v2.1) and 3500/01 Software (v3.30).
- Configure individual channel setpoints and filtering using 3500 Rack Configuration Software.
- Verify DC gap voltages on all connected proximity probes before enabling alarm relays.
System Compatibility & Certifications
The 3500/40-03-00 integrates into standard 19-inch 3500 rack enclosures.
It pairs with Bently Nevada 3300 XL 8 mm and NSv proximity transducer systems.
Packaging, Shipping & Warranty Terms
- Product Condition: Brand New & Original in Factory Sealed Packing.
- Factory Warranty: Guaranteed by a 12 Months Factory Warranty.
- Fast Dispatch: Ships within 24 to 48 hours after payment verification.
- Global Express Delivery: Shipped worldwide via express couriers FedEx, UPS, and DHL.
Suitable Equipment & Diagnostic Capabilities
Reliability teams deploy the 3500/40-03-00 on critical rotating machinery.
- Steam & Gas Turbines: Measures shaft radial vibration and axial rotor thrust position.
- Multistage Centrifugal Compressors: Tracks shaft orbit trajectories and dynamic balance changes.
- Rolling Element Bearings: Uses REBAM channels to detect microscopic outer race defects.
- Diagnostic Output: Sends raw waveform data to System 1 software for predictive maintenance.
Global PLC Spare HUB's Insight
Selecting option -03 simplifies hazardous area installations by integrating Zener barriers directly into the I/O card.
During retrofits, this eliminates external barrier cabinets and reduces panel wiring overhead significantly.
When configuring REBAM channels on boiler feed pumps, confirm your rack controller runs firmware v2.1 or higher.
Always land the IS ground wire on a low-impedance bus to guarantee barrier protection performance.
Purchasing Guide & Frequently Asked Questions
Q: Can I connect external termination blocks to an internal termination I/O module?
A: No, external termination blocks cannot connect to internal termination I/O modules like option -03.
Q: What is the main benefit of integrated internal barriers on option -03?
A: They provide intrinsic safety protection for hazardous locations without requiring separate DIN-rail barrier housing.
Q: What software version do I need to run REBAM rolling element bearing channels?
A: You need 3500/40M module firmware revision 2.1 and 3500/01 software version 3.30 or higher.
Q: How do buffered coaxial outputs help site maintenance engineers during troubleshooting?
A: They provide clean, isolated raw vibration signals for portable analyzers without risk of tripping the monitor.
Q: How fast will my spare monitor ship after I place an order?
A: We dispatch factory-sealed units within 24 to 48 hours using express DHL, FedEx, or UPS service.
Tags
Q: Are these parts 100% original and new?
A: Yes. Every component is guaranteed to be 100% original, brand-new, and factory-sealed. We also provide a 12-month comprehensive warranty for your peace of mind.
Q: How fast is the shipping to my country?
A: For in-stock items, we offer same-day dispatch. International express shipping (DHL/FedEx/UPS) typically delivers within 3–5 business days worldwide.
Q: Can I get a formal quotation with shipping costs?
A: Absolutely. Our sales team is ready to provide a detailed Proforma Invoice (PI) including the most competitive shipping rates for your location.
Q: Do you offer discounts for bulk orders?
A: We provide volume-based pricing for large projects or multiple-item orders. Please contact us to get our Best Price Guarantee.
12-Month Comprehensive Warranty
Every part supplied by Global PLC Spare Hub is covered by a 12-month warranty from the date of invoice.
- Coverage: Functional defects and hardware failures under normal operating conditions.
- Commitment: We provide immediate repair, replacement, or a full refund for any verified defective components to minimize your operational downtime.
Returns & Exchange Policy
We offer a 30-day return policy to ensure you receive the exact part your system requires.
- Eligibility: Returns are accepted for uninstalled items in their original, factory-sealed packaging.
- RMA Process: Please contact our support team to obtain a Return Merchandise Authorization (RMA) number before shipping.
- Fast Processing: Refunds or exchanges are processed within 3–5 business days after the returned item passes our technical inspection.
Need Technical Assistance?Not sure if this part is compatible with your system? [Consult our Engineers] before purchasing to ensure 100% compatibility.
People Also Bought
