NFLR121-S50 Serial Communication Module Yokogawa FCN
Manufacturer: Yokogawa
Product No.: NFLR121-S50
Condition: In stock
Product Type: Communication Module
Product Origin: SG
Payment: T/T, Western Union
Weight: 300g
Shipping port: Xiamen
Warranty: 12 months
Estimate delivery times: 12-26 days (International), 3-6 days (United States).
Return within 30 days of purchase. Duties & taxes are non-refundable.
Guaranteed Safe Checkout
Architectural Overview
The Yokogawa NFLR121-S50 is a dual-port RS-422/RS-485 serial communication interface engineered for STARDOM autonomous controllers. Designed for seamless backplane integration inside FCN and FCJ racks, this module bridges PLC subsystems, smart field instruments, and legacy Modbus RTU/ASCII nodes. It supports start-stop asynchronous transmission across 12 selectable baud rates up to 115.2 kbps over multipoint topologies reaching 1200 meters.
Suffix & Configuration Breakdown
Each suffix character in the NFLR121-S50 order code defines specific hardware protection and functional tiers:
-
Model Core: NFLR121 — 2-Port RS-422/RS-485 Serial Communication Module (300 bps to 115.2 kbps)
- Suffix -S: Standard ambient temperature hardware architecture
- Option 5: General-purpose industrial build (No explosion protection certification)
- Option 0: Basic functional firmware and hardware configuration
Hardware & Protocol Specifications
| Specification Category | Engineering Value |
|---|---|
| Manufacturer & System | Yokogawa — STARDOM FCN / FCJ Controller Platform |
| Order Model Code | NFLR121-S50 |
| Physical Interface | 2 Independent RS-422 / RS-485 Serial Ports |
| Topology & Duplexing | Multipoint connection; Half-duplex and Full-duplex operation |
| Synchronization Method | Start-stop asynchronous synchronization |
| Baud Rate Selection | 0.3, 1.2, 2.4, 4.8, 9.6, 14.4, 19.2, 28.8, 38.4, 57.6, 76.8, 115.2 kbps |
| Data Frame Formatting | Code: ASCII/Binary | Char: 7/8 bits | Stop: 1/2 bits | Parity: None/Even/Odd |
| Max Bus Span | 1200 meters total extended cable length |
| Field Termination | Clamped M4 screw terminal block (5 poles × 2 ports) |
| Rack Density Limit | Maximum 8 modules per FCN controller node |
| Current Draw & Mass | 500 mA backplane consumption; 0.3 kg net module weight |
Field Wiring & Rack Commissioning
- Verify Backplane Power Budget: Account for the 500 mA current draw per NFLR121-S50 unit when populating up to 8 modules in an FCN chassis.
- Terminate Twisted-Pair Conductors: Land shielded twisted-pair signal leads onto the 5-pole M4 screw terminals using ring or fork crimp lugs.
- Configure Bus Termination: Install external 120-ohm termination resistors across the far-end RX/TX differential lines on long 1200 m runs.
- Align Framing Registers: Match character length, stop bits, and parity settings inside STARDOM Logic Designer to your slave field devices.
Warranty & Global Fulfillment
- 12-Month Hardware Warranty: Every Yokogawa NFLR121-S50 module includes a full 12-month operational guarantee covering electronic and port defects.
- Express International Dispatch: Orders ship globally via FedEx, UPS, or DHL air freight to minimize unscheduled plant downtime.
Engineering Selection Guide
Specify the NFLR121-S50 when integrating multi-drop RS-485 power meters, analyzers, or variable frequency drives into safe-area STARDOM cabinets. If your installation requires Zone 2 hazardous area compliance or expanded operating temperature tolerances, verify alternative suffix codes within the NFLR121 family before ordering.
Frequently Asked Questions (FAQ)
Q1: How do I prevent signal reflections when running the NFLR121-S50 near its 1200-meter maximum distance?
A1: Install matched 120-ohm termination resistors at both physical ends of the trunk line and limit baud rates to 19.2 kbps or lower on long runs.
Q2: Can Port 1 and Port 2 operate with completely different serial framing parameters simultaneously?
A2: Yes, both serial ports are electrically and logically independent, allowing simultaneous polling of different baud rates, parity modes, and ASCII or binary protocols.
Q3: What is the difference between 2-wire half-duplex and 4-wire full-duplex wiring on the 5-pole M4 terminal block?
A3: Four-wire full-duplex separates transmit and receive pairs across four terminals, whereas two-wire half-duplex jumpers the TX+ to RX+ and TX- to RX- pins.
Q4: Why does my FCN controller reject communication when installing a ninth serial card?
A4: The FCN system architecture enforces a strict hardware limit of 8 NFLR121 modules per controller station to guarantee deterministic bus scan cycles.
Q5: When should an engineer choose the -S50 suffix over other NFLR121 variants?
A5: Select the -S50 code for standard non-hazardous indoor control rooms where explosion-proof certification and wide-temperature conformal coating are unnecessary.
Tags
Q: Are these parts 100% original and new?
A: Yes. Every component is guaranteed to be 100% original, brand-new, and factory-sealed. We also provide a 12-month comprehensive warranty for your peace of mind.
Q: How fast is the shipping to my country?
A: For in-stock items, we offer same-day dispatch. International express shipping (DHL/FedEx/UPS) typically delivers within 3–5 business days worldwide.
Q: Can I get a formal quotation with shipping costs?
A: Absolutely. Our sales team is ready to provide a detailed Proforma Invoice (PI) including the most competitive shipping rates for your location.
Q: Do you offer discounts for bulk orders?
A: We provide volume-based pricing for large projects or multiple-item orders. Please contact us to get our Best Price Guarantee.
12-Month Comprehensive Warranty
Every part supplied by Global PLC Spare Hub is covered by a 12-month warranty from the date of invoice.
- Coverage: Functional defects and hardware failures under normal operating conditions.
- Commitment: We provide immediate repair, replacement, or a full refund for any verified defective components to minimize your operational downtime.
Returns & Exchange Policy
We offer a 30-day return policy to ensure you receive the exact part your system requires.
- Eligibility: Returns are accepted for uninstalled items in their original, factory-sealed packaging.
- RMA Process: Please contact our support team to obtain a Return Merchandise Authorization (RMA) number before shipping.
- Fast Processing: Refunds or exchanges are processed within 3–5 business days after the returned item passes our technical inspection.
Need Technical Assistance?Not sure if this part is compatible with your system? [Consult our Engineers] before purchasing to ensure 100% compatibility.



