{"product_id":"bently-nevada-21505-00-60-05-02-7200-series-precision-vibration-probe","title":"Bently Nevada 21505-00-60-05-02 | 7200 Series Precision Vibration Probe","description":"\u003ch2\u003e\u003cstrong\u003e21505-00-60-05-02 Bently Nevada 7200 Proximity Vibration Probe\u003c\/strong\u003e\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eBently Nevada 21505-00-60-05-02\u003c\/strong\u003e is an 8 mm proximity probe for non-contact displacement and vibration measurement. It belongs to the \u003cstrong\u003e7200 Proximity Transducer System\u003c\/strong\u003e and uses a 3\/8-24 threaded mounting configuration. Its stainless-steel armored lead helps protect the cable in demanding machinery installations.\u003c\/p\u003e\n\u003cp\u003eThis configuration includes a 0.5 m total length and a miniature male coaxial connector. Engineers can use it for shaft vibration monitoring and relative shaft displacement measurement when the complete transducer system matches the required electrical characteristics.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Bently Nevada\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eModel:\u003c\/strong\u003e 21505-00-60-05-02\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSeries:\u003c\/strong\u003e 7200 Proximity Transducer Systems\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct type:\u003c\/strong\u003e Proximity vibration probe\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCondition:\u003c\/strong\u003e New and original in factory packing\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFactory warranty:\u003c\/strong\u003e 12 months\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003e\u003cstrong\u003e01 | Configuration Breakdown — Read the Suffix Before Ordering\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp\u003eUse the following configuration tree to verify the requested assembly against the existing installation.\u003c\/p\u003e\n\u003cpre\u003e21505 - 00 - 60 - 05 - 02\n  │      │    │    │    └── 02: Miniature male coaxial connector\n  │      │    │    └─────── 05: 0.5 m total length (20 in)\n  │      │    └──────────── 60: 6.0 in overall case length\n  │      └───────────────── 00: 0.0 in unthreaded length\n  └──────────────────────── 21505: 7200 proximity probe family\u003c\/pre\u003e\n\u003cp\u003e\u003cstrong\u003eConstruction details:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eProbe diameter:\u003c\/strong\u003e 8 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread:\u003c\/strong\u003e 3\/8-24\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCase:\u003c\/strong\u003e Standard configuration\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLead armor:\u003c\/strong\u003e Stainless steel armor\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector:\u003c\/strong\u003e Miniature male coaxial connector\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eEngineering check:\u003c\/strong\u003e Confirm the installed probe's thread, case geometry, cable routing, connector interface, and required target gap. Do not assume that a matching model-family name guarantees interchangeability.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e02 | Technical Data at a Glance\u003c\/strong\u003e\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003cth\u003eEngineering significance\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower supply\u003c\/td\u003e\n\u003ctd\u003e-17.5 to -26 VDC\u003c\/td\u003e\n\u003ctd\u003eVerify the compatible driver or Proximitor supply before connection.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaximum power consumption\u003c\/td\u003e\n\u003ctd\u003e12 mA\u003c\/td\u003e\n\u003ctd\u003eCheck supply capacity and system wiring requirements.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCalibrated range\u003c\/td\u003e\n\u003ctd\u003e80 mils (2.0 mm)\u003c\/td\u003e\n\u003ctd\u003eDefines the specified displacement measurement range.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRange start\u003c\/td\u003e\n\u003ctd\u003eApproximately 10 mils (0.25 mm) from the probe face\u003c\/td\u003e\n\u003ctd\u003eSet the target gap using the applicable system calibration procedure.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eScale factor\u003c\/td\u003e\n\u003ctd\u003e200 mV\/mil (7.87 V\/mm), ±4% when calibrated as a system\u003c\/td\u003e\n\u003ctd\u003eImportant for converting output voltage into displacement.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInterchangeability accuracy\u003c\/td\u003e\n\u003ctd\u003eWithin ±9.5%, including interchangeability errors\u003c\/td\u003e\n\u003ctd\u003eConsider this tolerance when replacing a probe without full system calibration.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLinearity\u003c\/td\u003e\n\u003ctd\u003eWithin 0.8 mil (0.02 mm) when calibrated as a system\u003c\/td\u003e\n\u003ctd\u003eRelevant to measurement accuracy across the calibrated range.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLinearity including interchangeability\u003c\/td\u003e\n\u003ctd\u003eWithin 2.3 mils (0.06 mm)\u003c\/td\u003e\n\u003ctd\u003eAllow for additional error when components are interchanged.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFrequency response\u003c\/td\u003e\n\u003ctd\u003e0–10 kHz; -5% at 10 kHz\u003c\/td\u003e\n\u003ctd\u003eSupports vibration measurements within the specified response range.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTemperature sensitivity\u003c\/td\u003e\n\u003ctd\u003eSource data indicates a scale-factor change at +65°C and a 1.27 mm gap; exact value requires verification.\u003c\/td\u003e\n\u003ctd\u003eConfirm the official specification before using temperature compensation calculations.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProximitor operating temperature\u003c\/td\u003e\n\u003ctd\u003e-51°C to +100°C\u003c\/td\u003e\n\u003ctd\u003eApplies to the Proximitor, not automatically to the probe assembly.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProbe and extension cable temperature\u003c\/td\u003e\n\u003ctd\u003e-34°C to +177°C\u003c\/td\u003e\n\u003ctd\u003eCheck actual ambient and cable exposure temperatures.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRelative humidity\u003c\/td\u003e\n\u003ctd\u003eUp to 95%, noncondensing\u003c\/td\u003e\n\u003ctd\u003ePrevent condensation and protect connectors from moisture ingress.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSystem weight\u003c\/td\u003e\n\u003ctd\u003e0.59 kg (1.3 lb)\u003c\/td\u003e\n\u003ctd\u003eSource-listed system weight; verify the shipping or assembly weight if required.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eData verification note:\u003c\/strong\u003e The supplied temperature-sensitivity figure contains a corrupted numeric value. This page does not infer or publish a replacement value. Confirm it against the applicable manufacturer documentation before engineering calculations.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e03 | Measurement Principle and Diagnostic Value\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp\u003eThe probe forms part of a proximity transducer system. The compatible driver converts the probe's interaction with a conductive target into an electrical signal that represents target displacement.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eShaft vibration:\u003c\/strong\u003e Supplies a displacement signal for monitoring relative shaft motion when installed with a compatible driver and monitoring channel.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShaft position trends:\u003c\/strong\u003e Helps engineers compare displacement trends against established machine baselines.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVibration investigation:\u003c\/strong\u003e Provides input for investigating changes associated with rotor vibration, bearing behavior, or operating-condition changes.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSignal-chain checks:\u003c\/strong\u003e Supports troubleshooting when engineers compare probe output, gap voltage, driver compatibility, cabling, and monitor readings.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eDiagnostic limitation:\u003c\/strong\u003e The probe alone does not identify a specific fault or provide a complete machinery-protection function. Reliable diagnosis requires suitable signal conditioning, correct installation, monitor configuration, and operating-history analysis.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e04 | Suitable Equipment and Applications\u003c\/strong\u003e\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eEquipment or application\u003c\/th\u003e\n\u003cth\u003ePotential use\u003c\/th\u003e\n\u003cth\u003ePre-installation check\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eIndustrial turbines\u003c\/td\u003e\n\u003ctd\u003eRelative shaft vibration and displacement monitoring\u003c\/td\u003e\n\u003ctd\u003eConfirm target material, mounting geometry, system compatibility, and required monitoring range.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCentrifugal compressors\u003c\/td\u003e\n\u003ctd\u003eRotor vibration monitoring and trend analysis\u003c\/td\u003e\n\u003ctd\u003eVerify probe location, cable routing, and the complete transducer's frequency response.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePumps and rotating machinery\u003c\/td\u003e\n\u003ctd\u003eNon-contact shaft-motion measurement\u003c\/td\u003e\n\u003ctd\u003eConfirm shaft surface suitability and the machine manufacturer's sensor arrangement.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eGearboxes and high-speed rotating equipment\u003c\/td\u003e\n\u003ctd\u003eDisplacement signal input for condition monitoring\u003c\/td\u003e\n\u003ctd\u003eCheck target runout, mechanical clearance, and the required measurement bandwidth.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eExisting 7200 monitoring installations\u003c\/td\u003e\n\u003ctd\u003eReplacement of a compatible probe assembly\u003c\/td\u003e\n\u003ctd\u003eMatch the complete part number, driver, connector, cable arrangement, and calibration requirements.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eApplication suitability depends on the complete installation design. Confirm the system architecture and the machine's monitoring requirements before selecting this probe for a protection loop.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e05 | Installation and Commissioning Checks\u003c\/strong\u003e\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eVerify the part number:\u003c\/strong\u003e Match all suffixes with the existing assembly and installation drawing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspect the mounting point:\u003c\/strong\u003e Check the 3\/8-24 thread, available clearance, and mechanical condition before installation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspect the armored lead:\u003c\/strong\u003e Check for crushed sections, sharp bends, damaged armor, and connector contamination.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConfirm driver compatibility:\u003c\/strong\u003e Verify the probe and driver combination against the manufacturer's system documentation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSet the target gap:\u003c\/strong\u003e Follow the approved system calibration procedure rather than relying on physical spacing alone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCheck the signal:\u003c\/strong\u003e Compare gap voltage, displacement output, and monitor readings with the commissioning baseline.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRecord the baseline:\u003c\/strong\u003e Document installation details and initial readings to support future fault investigation.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eDo not connect the probe directly to a PLC analog input unless the interface design includes the required compatible signal conditioning. Verify the actual output interface before wiring.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e06 | Global PLC Spare HUB’s Insight\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp\u003eDuring a probe replacement, engineers should verify the entire measurement chain rather than matching only the probe diameter. A different cable length, connector, driver, or calibration arrangement can affect installation and signal interpretation.\u003c\/p\u003e\n\u003cp\u003eFor example, if a vibration monitor reports an unexpected displacement after maintenance, first check the connector seating, cable condition, driver compatibility, and gap voltage. Then compare the installed configuration with the original commissioning record. This sequence helps separate installation errors from genuine changes in machine behavior.\u003c\/p\u003e\n\u003cp\u003eFor critical rotating equipment, preserve the existing measurement baseline whenever possible. If a replacement introduces different interchangeability tolerances, follow the approved recalibration procedure before relying on alarm or trip thresholds.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e07 | Selection Comparison: 21505-00-60-05-02 vs. 21505-22-55-10-02\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp\u003eCompare the requested probe with the following alternative before placing an order:\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAlternative model:\u003c\/strong\u003e \u003ca href=\"https:\/\/www.plcsparehub.com\/products\/21505-22-55-10-02-bently-nevada-7200-series-proximity-vibration-probe\"\u003e21505-22-55-10-02 Bently Nevada 7200 Series Proximity Vibration Probe\u003c\/a\u003e\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eSelection item\u003c\/th\u003e\n\u003cth\u003e21505-00-60-05-02\u003c\/th\u003e\n\u003cth\u003e21505-22-55-10-02\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eSeries\u003c\/td\u003e\n\u003ctd\u003e7200 Proximity Transducer Systems\u003c\/td\u003e\n\u003ctd\u003e7200 Series, based on the supplied product reference\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eUnthreaded length\u003c\/td\u003e\n\u003ctd\u003e00: 0.0 in\u003c\/td\u003e\n\u003ctd\u003eMust be verified against the applicable manufacturer documentation.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOverall case length\u003c\/td\u003e\n\u003ctd\u003e60: 6.0 in\u003c\/td\u003e\n\u003ctd\u003eMust be verified against the applicable manufacturer documentation.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTotal length\u003c\/td\u003e\n\u003ctd\u003e05: 0.5 m (20 in)\u003c\/td\u003e\n\u003ctd\u003eMust be verified against the applicable manufacturer documentation.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnector option\u003c\/td\u003e\n\u003ctd\u003e02: Miniature male coaxial connector\u003c\/td\u003e\n\u003ctd\u003eMust be verified against the applicable manufacturer documentation.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRecommended selection basis\u003c\/td\u003e\n\u003ctd\u003eUse when the documented mounting dimensions, lead length, and connector match the existing installation.\u003c\/td\u003e\n\u003ctd\u003eChoose only after confirming its full suffix configuration and compatibility with the installed system.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eTechnical recommendation:\u003c\/strong\u003e Do not select the alternative based on the shared 21505 model prefix alone. Obtain its official suffix definitions and compare mounting dimensions, total length, connector type, and driver compatibility. If the existing installation uses the 00-60-05-02 configuration, the same complete part number is the more straightforward replacement candidate, subject to verification of the original system documentation.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e08 | Maintenance and Troubleshooting Guidance\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eUnexpected vibration readings:\u003c\/strong\u003e Check the probe gap, connector seating, cable integrity, driver compatibility, and monitor channel configuration.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUnstable output:\u003c\/strong\u003e Inspect the armored lead and connectors for mechanical damage or contamination. Compare readings with the baseline before changing alarm settings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInconsistent replacement readings:\u003c\/strong\u003e Verify the installed part number and calibration method. Account for interchangeability tolerances where applicable.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTemperature-related concerns:\u003c\/strong\u003e Compare actual probe, cable, and driver temperatures with their respective limits. Do not apply the driver temperature range to the probe assembly.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSuspected sensor failure:\u003c\/strong\u003e Isolate the fault through approved maintenance procedures and compatible test equipment. Do not condemn the probe solely from a monitor alarm.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003e\u003cstrong\u003e09 | Packaging, Warranty, and Shipping\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct condition:\u003c\/strong\u003e New and original in factory packing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWarranty:\u003c\/strong\u003e 12-month factory warranty, subject to the applicable purchase terms.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShipping methods:\u003c\/strong\u003e FedEx, UPS, and DHL, subject to destination and service availability.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOrder verification:\u003c\/strong\u003e Confirm the full part number and required configuration before shipment.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003e\u003cstrong\u003e10 | Frequently Asked Questions\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eQ1. What information should I provide when requesting a replacement quotation?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eProvide the complete part number, installed driver model, connector details, cable arrangement, and machine application. A photo of the nameplate and mounting point can help confirm configuration details.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ2. Can I replace the probe without recalibrating the monitoring channel?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eDo not assume recalibration is unnecessary. Review the manufacturer’s replacement procedure and interchangeability tolerances. Follow site requirements for verifying gap voltage, signal scaling, alarm thresholds, and baseline readings.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ3. How can I distinguish a probe problem from a monitor-channel problem?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eCompare the probe assembly, driver, wiring, and channel configuration systematically. Use approved test procedures and known-good compatible components where permitted. A single abnormal monitor reading does not prove the probe has failed.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ4. What should I check when the replacement fits mechanically but produces different readings?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eCheck the complete suffix configuration, driver compatibility, target gap, cable condition, and calibration settings. Also review shaft surface condition and electrical interference before attributing the difference to sensor failure.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ5. Is this probe suitable for every Bently Nevada 7200 installation?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eNo. A shared series designation does not establish full interchangeability. Confirm the driver, connector, mounting dimensions, required cable length, measurement range, and monitoring-system documentation before ordering.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003eRequest a Quote\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp\u003eContact Global PLC Spare HUB with the complete model number \u003cstrong\u003e21505-00-60-05-02\u003c\/strong\u003e and your application requirements. Our team can help review the supplied configuration details and shipping options before you order.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":45013941059766,"sku":"21505-00-60-05-02","price":169.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/7863\/8774\/files\/Bently21505_14_a04aef31-b9b8-44ac-be78-89399de65aa7.jpg?v=1792467712","url":"https:\/\/www.plcsparehub.com\/products\/bently-nevada-21505-00-60-05-02-7200-series-precision-vibration-probe","provider":"Global PLC Spare Hub","version":"1.0","type":"link"}