{"product_id":"abb-feca-01-feca-series-ethercat-adapter-module","title":"ABB FECA-01 FECA Series EtherCAT Adapter Module","description":"\u003ch2\u003e\u003cstrong\u003eABB FECA-01 EtherCAT Adapter Module\u003c\/strong\u003e\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eABB FECA-01\u003c\/strong\u003e is a drive-mounted EtherCAT adapter module designed for high-speed communication between compatible ABB drives and EtherCAT-based automation systems. It uses 100BASE-TX Ethernet physical-layer communication at 100 Mbit\/s, with full-duplex transmission and a daisy-chain network topology.\u003c\/p\u003e\n\u003cp\u003eFor motion-oriented applications, the \u003cstrong\u003eFECA-01\u003c\/strong\u003e supports either the CANopen® DSP 402 Device Profile for Drives and Motion Control or the ABB drives profile. The selected profile should match the drive configuration, controller implementation, and application requirements.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e01 | Communication Architecture at a Glance\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eProtocol:\u003c\/strong\u003e EtherCAT\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePhysical medium:\u003c\/strong\u003e 100BASE-TX\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTransfer rate:\u003c\/strong\u003e 100 Mbit\/s\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCommunication mode:\u003c\/strong\u003e Full duplex\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNetwork topology:\u003c\/strong\u003e Daisy chain\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMaximum segment length:\u003c\/strong\u003e 100 m\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCable options:\u003c\/strong\u003e Cat 5e FTP or STP; UTP is also listed in the supplied specifications\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNetwork connectors:\u003c\/strong\u003e Two 8P8C modular jacks (X1 and X2)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDrive connection:\u003c\/strong\u003e 20-pin connector (X3)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eModule installation:\u003c\/strong\u003e Drive option slot\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eProtection rating:\u003c\/strong\u003e IP20\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePower supply:\u003c\/strong\u003e +3.3 V DC ±5%, maximum 450 mA, supplied by the drive\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIndicators:\u003c\/strong\u003e Two green LEDs and one bicolor LED, identified for LINK\/ACT and STATUS indication\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eEMC compliance:\u003c\/strong\u003e EN 61800-3:2004\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePCB construction:\u003c\/strong\u003e Conformal-coated printed circuit board\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDevice compatibility:\u003c\/strong\u003e EtherCAT-compliant devices, subject to drive and system compatibility\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e02 | How the FECA-01 Fits into a Drive Network\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp\u003eThe FECA-01 installs in the designated option slot of a compatible ABB drive. Its X3 connector provides the interface to the drive, while X1 and X2 connect the module to the EtherCAT network.\u003c\/p\u003e\n\u003cp\u003eThe two network ports support a daisy-chain arrangement between EtherCAT nodes. When planning the network, engineers should confirm the controller's port arrangement, the required communication profile, cable routing, and the segment-length limit. Each Ethernet segment must remain within the specified maximum of 100 m.\u003c\/p\u003e\n\u003cp\u003eThe adapter receives its operating power from the drive. It does not use a separate external power supply according to the supplied specifications. Before installation, verify the drive's option-slot compatibility and follow the applicable drive manual for isolation, insertion, and commissioning procedures.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e03 | Typical Equipment and Application Scenarios\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eABB variable-frequency drives:\u003c\/strong\u003e Enables EtherCAT communication where the specific drive model and firmware support the FECA-01 option.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMotion-control systems:\u003c\/strong\u003e Supports drive integration using the CANopen® DSP 402 profile or ABB drives profile, depending on the selected configuration.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePackaging and material-handling machinery:\u003c\/strong\u003e Can form part of an EtherCAT network used to coordinate drive control and exchange operating data.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eProduction and process equipment:\u003c\/strong\u003e Provides a communication interface for compatible drives in automated production lines, conveyor systems, and other networked machinery.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMachine retrofits:\u003c\/strong\u003e May be considered when integrating a compatible ABB drive into an existing EtherCAT architecture. Confirm controller support, profile requirements, firmware, and electrical compatibility before replacing or adding an adapter.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e04 | Commissioning Checks and Diagnostic Guidance\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eLINK\/ACT indication is absent:\u003c\/strong\u003e Check the Ethernet cable, connector seating, adjacent node, and port assignment. Confirm that the connected device is powered and that the cable type and segment length meet the installation requirements.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNetwork communication is unstable:\u003c\/strong\u003e Inspect cable condition, shielding, routing near power conductors, connector termination, and the daisy-chain path. Replace suspect patch cables with a verified Cat 5e cable and test the affected segment separately.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe drive does not exchange expected process data:\u003c\/strong\u003e Verify that the controller configuration uses the correct EtherCAT device description and the intended communication profile. Check the drive's option configuration, controller mapping, and applicable firmware compatibility.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe module is not recognized by the drive:\u003c\/strong\u003e Confirm that the FECA-01 is supported by the exact drive model and that it is fully seated in the designated option slot. Follow the manufacturer's power-isolation procedure before inspecting the connector or reinstalling the module.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSTATUS indication shows an abnormal condition:\u003c\/strong\u003e Read the LED state against the FECA-01 and drive manuals. The indicator colors alone do not establish a specific fault code; use the documented LED definitions and controller diagnostics to identify the cause.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSynchronization or motion behavior is incorrect:\u003c\/strong\u003e Confirm that the controller and drive use compatible profile settings and that the EtherCAT network is configured as intended. Check controller cycle settings, node state, drive parameters, and application-specific synchronization requirements. Do not assume that installing the adapter alone guarantees a particular motion-control performance level.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e05 | Global PLC Spare HUB's Insight\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp\u003eWhen selecting an EtherCAT adapter, the physical interface is only one part of the compatibility check. The FECA-01 provides 100 Mbit\/s full-duplex communication, but successful integration also depends on the ABB drive model, supported firmware, controller configuration, and selected drive profile.\u003c\/p\u003e\n\u003cp\u003eFor maintenance replacements, compare the complete part number and confirm the existing drive's option requirements before ordering. For new installations, review the network topology and cable specification early, especially where multiple drives are connected in a daisy chain. These checks help reduce commissioning delays and avoid purchasing an adapter that does not match the intended drive platform.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e06 | Product Selection and Handling Notes\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp\u003eBefore ordering the \u003cstrong\u003eABB FECA-01\u003c\/strong\u003e, confirm the following details with your drive documentation or equipment supplier:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eExact ABB drive model and supported option-slot configuration.\u003c\/li\u003e\n\u003cli\u003eController compatibility with EtherCAT and the intended communication profile.\u003c\/li\u003e\n\u003cli\u003eFirmware and configuration-tool requirements for the drive and controller.\u003c\/li\u003e\n\u003cli\u003eNetwork cable type, shielding approach, port layout, and segment length.\u003c\/li\u003e\n\u003cli\u003eRequired quantity and whether the adapter is for a new installation or a replacement.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe module has an IP20 protection rating. Install it in an enclosure and environment suitable for the associated drive. The ambient conditions specified in the drive's manuals apply; consult those manuals for temperature, humidity, and other installation limits.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e07 | Warranty, Shipping and Order Support\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWarranty:\u003c\/strong\u003e 12-month warranty, subject to the seller's written warranty terms.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eShipping options:\u003c\/strong\u003e FedEx, UPS, and DHL, subject to destination and service availability.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDispatch:\u003c\/strong\u003e Target dispatch within 24–48 hours where stock and order processing permit. Confirm actual availability and dispatch timing before placing an order.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTechnical support:\u003c\/strong\u003e Provide the drive model, existing adapter part number, controller type, and application requirements when requesting a quotation. This information helps verify compatibility before purchase.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003e08 | Frequently Asked Questions\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eQ1: What information should I provide to confirm FECA-01 compatibility with an ABB drive?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eProvide the complete drive type code, firmware version if available, and the existing communication-option details. Compatibility should be confirmed against the relevant ABB drive documentation rather than inferred from the EtherCAT connector alone.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ2: Can the FECA-01 be used in a network that includes devices from different manufacturers?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe supplied specifications state compatibility with EtherCAT-compliant devices. However, device-level interoperability also depends on the controller, device descriptions, supported functions, and configuration. Confirm the intended network and process-data requirements before deployment.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ3: How should I choose between the CANopen DSP 402 profile and the ABB drives profile?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eChoose the profile supported by both the controller configuration and the target drive application. DSP 402 is intended for drive and motion-control functions, while the ABB drives profile may be required by an existing ABB-oriented control setup. Check the relevant manuals before configuring the system.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ4: What should I check first if a replacement module powers up but the controller cannot communicate with the drive?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eStart with the LINK\/ACT and STATUS indications, then check the physical link, port connections, EtherCAT node configuration, and selected profile. Next, confirm that the drive recognizes the option and that the controller's device configuration matches the installed hardware. Use the documented LED definitions to narrow the fault.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ5: Is the FECA-01 suitable for every ABB drive that uses EtherCAT?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eNot necessarily. EtherCAT support at the system level does not guarantee that every drive accepts this particular adapter. Verify the drive's supported option modules, firmware requirements, and configuration instructions before ordering. If the exact drive model is available, include it in your quotation request for a more reliable selection check.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0722\/7863\/8774\/files\/FECA-01.png?v=1792994550\" alt=\"\"\u003e\u003c\/p\u003e","brand":"ABB","offers":[{"title":"Default Title","offer_id":67816095645878,"sku":"FECA-01","price":115.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0722\/7863\/8774\/files\/FECA-01-1_34d00281-4e6c-49bd-9e7a-e425efe2f57c.jpg?v=1792994574","url":"https:\/\/www.plcsparehub.com\/products\/abb-feca-01-feca-series-ethercat-adapter-module","provider":"Global PLC Spare Hub","version":"1.0","type":"link"}